agilent 33250A function/arbitrary waveform generator data sheet 80 mhz sine and square wave out- puts sine, square, ramp, noise and other waveforms 50 mhz pulse waveforms with vari- able rise/fall times 12-bit, 200 msa/s, 64k-point deep arbitrary waveform standard waveforms the agilent technologies 33250A function/arbitrary waveform generator uses direct digital-synthesis techniques to create a stable, accurate output on all waveforms, down to 1 hz frequency resolution. the benefits are apparent in every signal you produce, from the sine wave frequency accuracy to the fast rise/fall times of square waves, to the ramp linearity. front-panel operation of the 33250A is straightforward and user friendly. the knob or numeric keypad can be used to adjust frequency, amplitude and offset. you can even enter voltage values directly in vpp, vrms, dbm, or high/low levels. timing parameters can be entered in hertz (hz) or seconds. custom waveform generation why settle for a basic function genera- tor when you can get arbitrary wave- forms at no extra cost? with the 33250A, you can generate arbitrary waveforms with 12-bit vertical resolu- tion, 64k memory depth, and a sample rate of 200 msa/s. you can also store up to four 64k-deep arbitrary wave- forms in non-volatile memory with user-defined names to help you find the right waveform when you need it most. the included agilent intuilink soft- ware allows you to easily create, edit, and download complex waveforms using the intuilink arbitrary waveform editor. or you can capture a waveform using intuilink oscilloscope or dmm and send it to the 33250A for output. for programmers, activex components can be used to control the instrument using scpi commands. intuilink pro- vides the tools to easily create, down- load, and manage waveforms for your 33250A. to find out more about intuilink, visit www.agilent.com/find/intuilink . pulse generation the 33250A can generate simple pulses up to 50 mhz. with variable edge time, pulse width and voltage level, the 33250A is ideally suited to a wide variety of pulse applications. built-in versatility am, fm and fsk capabilities make it easy to modulate waveforms with or without a separate source. linear or logarithmic sweeps can be performed with a programmable frequency marker signal. programmable burst count and gating allow you to further customize your signal. for system applications, both gpib and rs-232 interfaces are standard, and support full programmability using scpi commands. color graphical display the unique design of the 33250A com- bines a low-profile instrument with the benefits of a color graphical display. now you can display multiple wave- form parameters at the same time. the graphical interface also allows you to modify arbitrary waveforms quickly and easily. timebase stability and clock reference the 33250A tcxo timebase gives you frequency accuracy of 2 ppm for your most demanding applications. the external clock reference input/output lets you synchronize to an external 10 mhz clock, to another 33250A, or to an agilent 33120a. phase adjust- ments can be made from the front panel or via a computer interface, allowing precise phase calibration and adjustment.
waveforms standard sine, square, pulse, ramp, noise, sin(x)/x, exponential rise, expo- nential fall, cardiac, dc volts arbitrary waveform length 1 to 64k points amplitude resolution 12 bits (including sign) repetition rate 1 ?z to 25 mhz sample rate 200 msa/s filter bandwidth 50 mhz non-vol. memory four (4) 64k waveforms frequency characteristics sine 1 ?z to 80 mhz square 1 ?z to 80 mhz pulse 500 ?z to 50 mhz arb 1 ?z to 25 mhz ramp 1 ?z to 1 mhz white noise 50 mhz bandwidth resolution 1 ?z; except pulse, 5 digits accuracy (1 year) 2 ppm, 18? to 28? 3 ppm, 0? to 55? sinewave spectral purity harmonic distortion 3 vpp 1 > 3 vpp dc to 1 mhz -60 dbc -55 dbc 1 to 5 mhz -57 dbc -45 dbc 5 to 80 mhz -37 dbc -30 dbc total harmonic distortion dc to 20 khz < 0.2% + 0.1 mvrms spurious (non-harmonic) 2 dc to 1 mhz -60 dbc 1 to 20 mhz -50 dbc 20 80 mhz -50 dbc + 6 dbc/octave phase noise (30 khz band) 10 mhz <-65 dbc (typical) 80 mhz <-47 dbc (typical) signal characteristics squarewave rise/fall time < 8 ns overshoot < 5% asymmetry 1% of period + 1 ns jitter (rms) < 2 mhz 0.01% + 525 ps 2 mhz 0.1% + 75 ps duty cycle 25 mhz 20.0% to 80.0% 25 to 50 mhz 40.0% to 60.0% 50 to 80 mhz 50.0% fixed pulse period 20.00 ns to 2000.0 s pulse width 8.0 ns to 1999.9 s variable edge time 5.00 ns to 1.00 ms overshoot < 5% jitter (rms) 100 ppm + 50 ps ramp linearity < 0.1% of peak output symmetry 0.0% - 100.0% arb min. edge time < 10 ns linearity < 0.1% of peak output settling time < 50 ns to 0.5% of final value jitter (rms) 30 ppm + 2.5 ns output characteristics amplitude (into 50 ? ) 10 mvpp to 10 vpp accuracy (at 1 khz, >10 mvpp, autorange) 1% of setting 1 mvpp flatness (sinewave relative to 1 khz, autorange) < 10 mhz 1% (0.1 db) 10 to 50 mhz 2% (0.2 db) 50 to 80 mhz 5% (0.4 db) units vpp, vrms, dbm, high and low level resolution 0.1 mv or 4 digits offset (into 50 ? ) 5 vpk ac + dc accuracy 1% of setting + 2 mv + 0.5% of amplitude waveform output impedance 50 ? typical (fixed) >10 m ? (output dis- abled) isolation 42 vpk maximum to earth protection short-circuit protected; overload automatically disables main output modulation am carrier waveforms sine, square, ramp, and arb mod. waveforms sine, square, ramp, noise, and arb mod. frequency 2 mhz to 20 khz depth 0.0% to 120.0% source internal/external fm carrier waveforms sine, square, ramp, and arb mod. waveforms sine, square, ramp, noise, and arb mod. frequency 2 mhz to 20 khz peak deviation dc to 80 mhz source internal/external fsk carrier waveforms sine, square, ramp, and arb mod. waveform 50% duty cycle square internal rate 2 mhz to 1 mhz frequency range 1 ?z to 80 mhz source internal/external external modulation input voltage range 5 v full scale input impedance 10 k ? frequency dc to 20 khz burst waveforms sine, square, ramp, pulse, arb, and noise frequency 1 ?z to 80 mhz 3 burst count 1 to 1,000,000 cycles or infinite start/stop phase -360.0 to +360.0 internal period 1 ms to 500 s gate source external trigger trigger source single manual trigger, internal, external trig trigger delay n-cycle, infinite 0.0 ns to 85.000 sec sweep waveforms sine, square, ramp, and arb type linear and logarithmic direction up or down start f/stop f 100 ?z to 80 mhz sweep time 1 ms to 500 s trigger single manual trigger, internal, external trig marker falling edge of sync sig- nal (programmable) 2
system characteristics configuration times (typical) function change standard 100 ms pulse 660 ms built-in arb 220 ms frequency change 20 ms amplitude change 50 ms offset change 50 ms select user arb < 900 ms for < 16k pts. modulation change < 200 ms arb download times gpib/rs-232 (115kbps) arb length binary ascii integer ascii real 64k points 48 sec 112 sec 186 sec 16k points 12 sec 28 sec 44 sec 8k points 6 sec 14 sec 22 sec 4k points 3 sec 7 sec 11 sec 2k points 1.5 sec 3.5 sec 5.5 sec trigger characteristics trigger input input level ttl compatible slope rising or falling, selectable pulse width > 100 ns input impedance 10 k ? , dc coupled latency burst < 100 ns (typical) sweep < 10 ? (typical) jitter (rms) burst 1 ns; except pulse, 300 ps sweep 2.5 ? trigger output level ttl compatible into 50 ? pulse width > 450 ns maximum rate 1 mhz fanout 4 agilent 33250A? clock reference phase offset range -360 to +360 resolution 0.001 external reference input lock range 10 mhz 35 khz level 100 mvpp to 5 vpp impedance 1 k ? nominal, ac coupled lock time < 2 s internal reference output frequency 10 mhz level 632 mvpp (0 dbm), nominal impedance 50 ? nominal, ac coupled sync output level ttl compatible into > 1 k ? impedance 50 ? nominal general power supply 100-240 v, 50-60 hz 100-127 v, 50-400 hz power consumption 140 va operating temp. 0? to 55? storage temp. -30? to 70? stored states 4 named user configura- tions power on state default or last interface ieee-488 and rs-232 std. language scpi-1997, ieee-488.2 dimensions (wxhxd) bench top 254 x 104 x 374 mm rackmount 213 x 89 x 348 mm weight 4.6 kg safety designed to en61010-1, csa1010.1, ul-311-1 emc tested to iec-61326-1 iec-61000-4-3 criteria b iec-61000-4-6 criteria b vibration and shock mil-t-28800e, type iii, class 5 acoustic noise 40 dba warm-up time 1 hour calibration interval 1 year warranty 1 year 3 1 harmonic distortion at low amplitudes is limited by a - 70 dbm floor 2 spurious noise at low amplitudes is limited by a -75 dbm floor 3 sine and square waveforms above 25 mhz only with infinite burst count
ordering information agilent 33250A function/arbitrary waveform generator accessories included operating manual, service manual, quick reference guide, intuilink connectivity soft- ware, test data, rs-232 cable, and power cord. options opt. 1cm rackmount kit* (agilent 34190a) accessories 10100c 50 ? feedthru 11094b 75 ? feedthru 11095a 600 ? feedthru 34131a carrying case 34161a accessory pouch 34190a rackmount kit* 34811a benchlink arb software *for racking two 33250As side-by-side, order the follow- ing items: lock-link kit (p/n 5061-9694) flange kit (p/n 5063-9212) agilent technologies?test and measurement support, services, and assistance agilent technologies aims to maximize the value you receive, while minimizing your risk and prob- lems. we strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. our extensive sup- port resources and services can help you choose the right agilent products for your applications and apply them successfully. every instrument and system we sell has a global warranty. support is available for at least five years beyond the production life of the product. two concepts underlie agilent's overall support policy: "our promise" and "your advantage." our promise our promise means your agilent test and mea- surement equipment will meet its advertised performance and functionality. when you are choosing new equipment, we will help you with product information, including realistic perfor- mance specifications and practical recommen- dations from experienced test engineers. when you use agilent equipment, we can verify that it works properly, help with product operation, and provide basic measurement assistance for the use of specified capabilities, at no extra cost upon request. many self-help tools are available. your advantage your advantage means that agilent offers a wide range of additional expert test and mea- surement services, which you can purchase according to your unique technical and business needs. solve problems efficiently and gain a competitive edge by contracting with us for cali- bration, extra-cost upgrades, out-of-warranty repairs, and on-site education and training, as well as design, system integration, project man- agement, and other professional engineering services. experienced agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on invest- ment of your agilent instruments and systems, and obtain dependable measurement accuracy for the life of those products. www.agilent.com/find/emailupdates get the latest information on the products and applications you select. for more information on agilent technologies products, applications or services, please con- tact your local office. the complete listing is available at: www.agilent.com/find/contactus phone or fax united states: (tel) 1 800 829 4444 (fax) 1 800 829 4433 canada: (tel) 1 877 894 4414 (fax) (905) 282 6495 china: (tel) 800 810 0189 (fax) 800 820 2816 japan: (tel) (81) 426 56 7832 (fax) (81) 426 56 7840 korea: (tel) (080) 769 0800 (fax) (080) 769 0900 latin america: headquarters: (tel) (305) 269 7500 taiwan: (tel) 0800 047 866 (fax) 0800 286 331 other asia pacific countries: (tel) (65) 6375 8100 (fax) (65) 6755 0042 (e-mail) tm_ap@agilent.com product specifications and descriptions in this document subject to change without notice. ?agilent technologies, inc. 2001, 2004 printed in usa july 14, 2004 5968-8807en
|
